How to Reset IP Camera Without Reset Button: 5 Easy Steps

Introduction

Do you want to reset your camera, but it doesn’t have a reset button? Well, don’t get frustrated over this. That’s because there is a trick to resetting the IP camera.

So, do you want to find out how to reset IP camera without reset button?

You need to start up by removing the lens from the camera. For this, use a screwdriver to remove all the screws. This will reveal the insides of the camera. Lastly, short circuit the wires to reset your camera. However, make sure the power is on when you do this.

But hold up, that’s not all. We promised you an entire article on this process, and that’s what we’re going to give you. So, stay tuned to get more info.

How to reset IP camera without reset button: 6 Steps

The reset button is pretty useful since it only takes one click to reset the entire camera. However, there are times when you don’t have a reset button. Other times you can’t find it you can still reset the camera.

For this, you have to follow our instructions. Do you think you can do that? Well, we know you can. So, buckle up because we’re about to go through the process.

Step 1- Remove the cover of the Lens

First things first, you have to remove the cover of the lens. This is because you need to reach the innermost part of the camera. Or else you won’t be able to fulfill your goal.

Hence take out something plain and strong to pull out the lens. You can go creative with this device but we recommend you to use a swiss knife.

Nevertheless, don’t use a sharpened knife. That may damage your camera. Speaking of which, be very careful while taking out the lens cover.

If you slip up you can end up scratching your lens. And trust us, that’ll leave a permanent mark. So, be a bit steady with your hands.

Step 2- Unscrew the screws

By now, you might have an idea about where we’re headed. Yep, we’ll be removing the entire lens from the camera. But while we proceed to do that, the screws will hinder the process.

So, what do you do with those screws? Well, you dive in with a screwdriver and remove those screws. Now, the number of screws will depend on your camera model.

Hence, make sure to remove all the screws necessary. This way, you’ll be able to remove the lens too.

Step 3- Take out the lens

Once all the hurdles are out of the way, you can proceed to remove the lens. Yep, the path is clear, so a single pull should take out all the inner components.

However, do proceed with caution. This is because the inner wires are still connected. So, if you pull the wires too hard, the entire system will fail.

Then your camera won’t operate at all. Nevertheless, do take out all the parts. There’s more work to be done.

Step 4- Short Circuit the wires

Is everything out yet? If it is, then take out your screwdriver. We’re going to mess around with the wires a bit.

Don’t worry; if you proceed with caution, everything will be ok. So, for this step, you need to identify the holes that pass the current along with the camera.

However, while you carry out this step, make sure the power is on. Or else the wires will not be able to pass on the current. And the entire thing will be a waste of time.

Anyway, once you have the holes in your sight, use the screwdriver to make a short circuit between them. That means you need to simply tap on the holes to allow the current to flow in the opposite direction.

Make sure to short circuit the wires for exactly 10 seconds. After that, you’ll be all set for the last and final step.

Step 5- Put everything back together

Lastly, tidy up the job by putting everything back in its place. And to seal the job, screw on the screws that you removed.

Once they’re back, turn on your camera and check if everything is okay or not. By now, your camera should be reset for you.

FAQ

Question: Where is the reset button on the IP camera?

Answer: Take out the entire lens of the camera and then unscrew the screws on the camera. For this, you need a screwdriver. After all the parts are out you should be able to see the reset button attached at the back of the lens.

Question: How do I factory reset my Hikvision IP camera?

Answer: To factory reset the Hikvision IP camera, you need to turn off the power. Then press on the reset button. Make sure you press on it for at least 10 seconds. After that, let go of the reset button, and the camera will restart.

Question: What is the default IP of Hikvision IP camera?

Answer: The IP address for Hikvision IP camera starts with 192.0.0.64 and the port includes 8000. The other numbers are your admin id and password.

Question: Can I connect an IP camera directly to my computer?

Answer: Yes, you can connect your IP camera to your computer. But for this, you need a power source for your camera and some basic skills to set up the connection.

Ending words

Well, that is all we have on how to reset IP camera without reset button. Remember, all you have to do is download the Hik-connect app and then make your way to the reset option.

That’ll reset your camera. And the best thing is you can do this while sitting at home. So, what are you waiting for? Try it out today!